Orders over $200 ship FREE to 48 States
 

All American Pull Buddy

• Reduces Time and Labor
• Reduces the chance of damaging wires
• Turns wire pulling into a one man job
  - Quantities Available - more info

BEND ALL Cable Bender

Perfectly sized for 4/0, it takes the pain out of 200 amp services or sub feeders. The conductors like it too. The Bend All makes micro adjustable bends without brutalizing the wire.

Fits #3 to 350 MCM conductors. Machined from 6061 Aircraft Aluminum - Fits on a standard 1/2" ratchet. - more

Booty Pack

Disposable Booty Covers, Gloves and Respirator -

Make a Good Impression with your Customers -
KEEP IT CLEAN!

Bigg Lugg Belt Clip Personal Tool Holders

Belt Clip Tool Carriers - 2 styles to choose from!  Called the most innovative and versatile tool holding system ever made!

Carry Cordless Power Drills, Nail Guns, Cordless Saws, Caulking Guns, Paint Buckets and more...  - more info

Butt Pouch Pocket Pro, the Pocket Tool Holder

+  DRILLER!

-

Butt Pouch is the Tool Pouch that fits right in your pocket! No Belt required. Large snap loop for attaching to your belt if preferred. Quick to put on and comfortable too. Made of ballistic nylon - 3 Models to choose from. - more

CableStik Multi-Purpose Cable Dispensing System

CableStik Multi-Purpose Cable Dispensing System -

• Fast, installs in seconds

• Requires no tools for installation

• Very compact, stores easily

• Max Load 130lb

• Stud-Mounted, Free-Standing and Hitch / Vehicle Mounting Capability more info

Circuit Siren - Audible Circuit Identifier

Circuit Siren - Audible Circuit Identifier

• 3 to 130 volt AC & DC
• Built in polarity lights
• Handy adapter fittings
• Adjustable volume control
• Includes FREE Adapter Set - more

Conduit Level - Torpedo Level with Laser

Laser Torpedo Levels don’t work too well if they keep falling off your pipe. Designed for metallic pipe, the Conduit Level has powerful magnets and a concave base to align the Laser Level with the pipe. Accurate to ± ¼ inch  @ 100 feet.

Three vials (0°, 45° and 90°) - Anodized aluminum construction - Can be attached to any compatible tripod. - Free carrying case and batteries -
This is a nice Level. - more

Croc's Needle-Nosed Wire Strippers

Croc's™! What a beautiful stripper. - Dual action sheath stripper, crimper, oversized cutters - and more!

• Romex sheath stripper at the "nose" where it is easier to use inside boxes

• Strips conductor sizes from #10 down to #22 AWG (for telephone wire)

• Large cutting blades for easy general purpose cuts - more

DRILLER'S Dust Bowl

You may enjoy a face full of drywall dust but your customers might not!

The flexible DRILLER'S Dust Bowl compresses and traps dust and debris as you drill. It fits your drill and holesaw without any adjustments. Put an end to 'unprotected holesawing' Fits Hole-Saws up to 8" diameter. - more

E-Z Roll Wheeled Wire Rack

Most wheeled wire dispensers are too big for your truck and they only hold little wire spools. The E-Z Roll Wire Rack knocks down in seconds and handles reels to 18 inches. (150 lb. Load Tested). Use a conduit bender or scrap of 1" EMT (not included) for an axle/handle.

The E-Z Roll is big enough to handle 1000' rolls of Romex., but small enough to fit in a Job Box.  Simple, Effective, Rigid Steel Construction and Light-weight Design. - more

Exploding Garbage Can Collapsible Trash Container

Who says you're a slob? Clean up your reputation with your own trash can. The Exploding Garbage Can will dazzle your customers, especially if you use it! Pops up and folds flat... ready when needed.

Featuring an internal support spring that "Springs into Action" - Heavy Duty, Tear Resistant Polytuf Fabric 19" x 24" (open) 1½" x 24" (collapsed) - more

Fish Sticks - Electrician's PVC Wire Pulling Rods

Pull or Push wire the Fast and Easy Way!

• 5 piece design makes it easy to get the length you need. Maximum assembled length - 10 feet.

• Includes 2 bull tip slotted heads for attaching wire.

• Safe, non-conductive flexible PVC plastic bends easily around obstacles.

• Set includes nylon carrying case.

Every Installer needs one of these! - more

Head-LITE Hat - the Hands-Free LED Flashlight

Hole in One Cutter

Cuts perfect circles in Sheetrock, Wood and Metal Every Time!

It's built tough to meet the needs of Electricians and other construction professionals. Adjustable radius blade cuts circles up to 10-1/4".

Impact-resistant clear Dust Cover shields users from flying chips, and catches dust and debris  - more

Hooker Pipe Wrench Adapter

Every RACK-A-TIER needs a HOOKER! - RACK-A-TIERS have always had a "pipe vise" capability with the 'V' notches. They set out to improve this function and succeeded beyond expectation.

A set of RACK-A-TIERS with a HOOKER pipe wrench adapter can stand in for a tripod or bench mounted pipe vise plus it's faster and easier to use. The HOOKER is far lighter, less expensive and fits all RACK-A-TIERS. - more

KO Killers - Plastic Knockout (KO) Fillers

KO Killers -

No more tools, hammers, flying metal fillers, exploding buss bars, etc. Needing no tools is a big plus, especially when working space is tight. They go in easily and stay in. KO Killers fit all electrical boxes, including heavy wall cabinets.

Fits thin (1/32”) and thick (1/8”) wall thickness.

Available in 1/2” through 2” trade sizes. - more

Laser Chalk Bob IV

 Laser Chalk-Bob IV can save hours on your jobs, helping you easily lay out fixture locations on vaulted ceilings and in High Bays areas.

Simply lay out the work on the floor (where it's easier - and safer to take measurements), position the laser over the locations and it will pinpoint the corresponding spot on the ceiling.

- more

Self-Leveling Vertical Laser Plumb Bob

Looking for a better way to lay out complex ceilings and high bays? - Tired of trying to measure ceiling work from the top of a ladder? - The RACK-A-TIERS^® Laser Plumb Bob enables you to lay out overhead work on the ground and then quickly transfer the measurements to the ceiling.

Factory aligned laser module calibrated to precise 0.15° accuracy - Magnetic damping for quick stabilization. - more

LB Wire Guide

LB Wire Guide -

‘SHOE HORN’ FOR 2” LB’S

• For PVC LB fittings & adaptable to most metal LB’s
• One man conductor installation
• Faster conductor installation
• Installs in two positions to fit both ‘Ends’ of the LB
• Helps prevent Conductor Damage - more

Level Jack - Low Voltage / Datacom Plaster Ring

Alignment tabs reach across wood/metal studs to level low voltage outlets with A.C. boxes. No tape measure / No level required.

Available in 1/2”, 5/8” and 1” rise. - more

Magnetizer / DeMagnetizer

Magnetizer / DeMagnetizer -

Magnetizes or demagnetizes driver bits, tools and small steel parts instantly!

Nut Spinner Wire Nut Installation Tool

Nut Spinner Wire Nut Installation Tool -

Spin Your Wire Nuts on instead of twisting! -

Much faster, easier and it really cinches them up.

• Fits most wire nuts (pigtails too!)
• Fast, secure wire nut installation
• No Pre-twisting required - more

Pipe Spring PVC Conduit Bender

Pipe Spring (Sched. 40 PVC) Bender -

PlugGrip and Tester

Never hold an electrical outlet with your fingers again!

For duplex outlet installations, hold the PlugGrip instead of the outlet! Insert the PlugGrip into the outlet before wiring to provide greater control over stiff electrical wires. Separate feed power warning lights will indicate power to receptacles. Works great for remodeling projects and speeds up new installations! Handy for leveling plugs. - more

proGrabit Damaged Screw Remover Kit

proGrabit Damaged Screw Remover Kit -

Just drill out the damaged screw / bolt with one end of the Grabit, then flip it over and the “grab end” winds out the screw.

Pull-Rite 'Wire Brake'

Full new rolls wound to the rim? - No longer a problem. Jerky pull with lots of stopping? - No more "bird's nesting". Just want one or two conductors from a group? - That's all that spins. One man pulls? - Easy, and the PULL-RITE is easy to install!.

It clips on each roll in seconds and fits standard #12 and #14 wire spools.

Buy a 3-Pack and Save! - more

RACK-A-TIERS Wire Dispensers

As a wire dispenser only, RACK-A-TIERS are hard to beat but they have many other uses. It's a good thing they're tough because they get a lot of use and you'll have them for a long time.

No moving parts, won't rust, rot, scratch your trunk, bash the doorframe, and they float. Nice and compact, RACK-A-TIERS earn their place in your truck. (sold in pairs) - more

Rack 'N Roller Wire Dispenser

Wire spools run on spring-loaded rollers, - no axle - Spools can be loaded one at a time without disturbing the others. - If you use a lot of THHN, this is your unit, especially for a service truck.

Easy to tow around, handles for lifting AND it's a piece of cake to change each roll out. It stores and protects your wire spools when not in use. - No axles or loose parts. Rugged Construction - 32" long - holds 4 - 5 rolls of THHN (10, 12, 14 AWG) - more

Racksy Pad Gel Knee Pads

Racksy Pad Gel Knee Pads -

Improved!

Now with GEL Implants!

Velcro/elastic straps make these knee pads easy to put on and take off. - more

RACKY Bits - Color Coded Drive Bits

COLOR coding? It’s so simple but it works. Racky Bits are easier to use and harder to lose and they make your job easier. If that’s not enough, our genuine Robertson® RACKY BITS have hardened tips that fit better and last longer. - more

RACKY Level - Magnetic Conduit Level

The Racky Level’s base combines powerful magnets with a clearly etched template designed to make measuring for boxes a snap. - more

REEL-END - Wire Spool Repair